How to Make a Hot Pad With Insul Bright? These bright and colorful DIY pot holders are not only a useful kitchen accessory but also a thoughtful present for friends and family. Making these heat-resistant pot holders is a great first sewing project. One of our goals for the new year is how to use and clean silicon Baking Mat? and to devote one day each week to a fun family outing.
A handful of days each year can get quite chilly where we are in Missouri. Light snowfall occurs, but it melts away rapidly. Nothing stays around for too long. Unfortunately, however, it has been unusually chilly recently. Temperatures in the single digits! To add insult to injury, being outside in these conditions is no fun at all with six children. Instead, we opted to have a stay-at-home family adventure day.
Tell me, how does this appear? We spent the day baking bread; creating a sourdough coffee cake; doing crafts; playing games; and just relaxing from our routine. Everything was OK; it was just a nice, quiet day at home.A day like today calls for a do-it-yourself pot holder. Making the pot holders took less than an hour each, and I was able to use up some waste fabric while bonding with my daughters in the process.
DIY Pot Holder Tips:
- If you’re looking for a way to recycle your fabric scraps, look no further. You won’t need a lot of materials to finish it.
- In order to prevent the fabric and insulation from bunching up, you should sew a couple lines of stitching down the middle. You can get away with only one line along the middle if you’re in a pinch.
- Check out my free online course if you have never picked up a needle and thread before and have no idea where to begin.
There are affiliate links in this post, which allow me to earn a profit at no additional cost to you. Please see my complete disclaimer here. It can be made resistant to heat in two different methods. To prevent the fabric from melting, use Insul-Bright batting or multiple layers of a heavier fabric. For details, please continue reading.
Possible Resources and Equipment:
fabric remnants 10 inches wide – denim, cotton, linen, grain sack, drop cloth, and just about anything else will do. Simply put, I wouldn’t recommend using particularly sheer materials.
Material for thermal insulation, such as cotton batting or Insul-Bright (a heat resistant batting, which is the best option). It’s also possible to use a drop cloth or a piece of old denim, in addition to flannel or dish towels.
How To Make a DIY Pot Holder:
First, you should measure your fabric and make markings. Two squares of fabric measuring 10 inches should be sliced off. One fabric strip measuring 112″ by 4″ will serve as the loop.
Insulating my handcrafted pot holders has been an ongoing experiment for me over the years (see above). Insul-Bright, a high-density polyester product, is your best bet. It appears to provide the best insulation when sandwiched between two layers of cotton quilt batting.
Don’t worry if you don’t have Insul-Bright; you can still use the alternatives discussed above. If you want to be sure the layers can withstand high temperatures without melting, you should do a quick test with a hot pan before you start sewing (be careful of course). If your hand is too hot after only a few seconds of holding it, you may want to rethink the fabric structure or add more layers.
- When folding the loop, make sure the right sides are together. Add a small seam, about 1/4 inch, to the long side.
- You can use a safety pin to quickly and easily flip the loop you just made inside out.
- The loop section must be flattened using an iron and then top stitched along the seam.
- .Put your insulation pieces in stacks of 10 inches on your table.
- Place the fabric right side out over the insulation.
- Turn the loop in half so that the raw edges are towards the corner, and put it there.
- On top of that, with right sides together, lay the remaining cloth with its wrong side facing outward.
- Sew the potholder together with a 1/2 inch seam. Split it open on one side by four inches.
- Trim the surplus insulation to reduce the bulk in the corners.
You can now use the slit you created to turn the pot holder right-side out. All the insulation can be concealed in here.